ultrasonic cleaner an appropriate amount of clean water can be added to adjust the cleaning solution, which is beneficial to the cleaning process of the ultrasonic cleaner and can be adjusted according to different cleaning objects. Among them, issues such as the dilution of the liquid agent and the saving of the liquid agent have all been resolved accordingly. 1. Add an appropriate amount of clean water to the ultrasonic cleaning tank. The water level should be such that the parts to be cleaned are fully submerged, generally not exceeding three quarters of the tank. Adjust the amount of cleaning agent according to different items. It can also achieve the same effect. 2. When the water temperature rises to around 40℃, add the UC-O3 component cleaning agent to the cleaning tank (generally about 5kg at a time), and slowly stir the clear water to ensure it is fully dissolved (at this point, you can also start the ultrasonic wave or activate the aeration device for stirring). 3. Before the ultrasonic cleaning machine is pre-treated, it is advisable to use a bamboo knife to simply clean the dirt on the surface of the parts (for example, the outer surface of the dust cover will have a lot of dust, and the cylinder block parts will accumulate a lot of thick and easy-to-remove oil sludge at the curve changes of the shell), so as to extend the service life of the cleaning solution. 4. Ultrasonic cleaning heating
Start the electric control heating switch and point the white scale line on the water temperature adjustment knob to the appropriate temperature (it should be around 60℃). During the operation of the cleaning machine, the maximum temperature of the cleaning agent should not exceed 70℃. Ultrasonic waves can perform precise cleaning, but their ability to handle mud-like contaminants is relatively weak. Therefore, during the pretreatment process, efforts should be made to remove yellow or thin mud-like contaminants as much as possible. 5. Ultrasonic cleaning machine parts placement
Place the components in the steel bar material basket and gently put them into the cleaning pool. When a large number of parts are placed at one time, they should be evenly distributed in the material basket as much as possible and not overlap. 6. When the ultrasonic cleaner is in normal operation, ultrasonic waves are emitted simultaneously from three directions. Press the side ultrasonic start button, and the ultrasonic waves on both sides have already started. Rotate the power adjustment knob to the right and press the side ultrasonic start button. And turn it to the appropriate power. At this point, the LED display shows the current bottom ultrasonic working power value. 7. When the ultrasonic cleaner is to be shut down during the cleaning process, the power knob should be adjusted to the minimum first. Press the stop bottom ultrasound again. The cleaning time should be determined based on the condition of the surface to be cleaned. 8. Ultrasonic cleaning machine overflow
If there is too much floating oil on the liquid surface of the cleaning tank. The overflow device of the cleaning machine should be opened to drain it to prevent secondary contamination of the workpieces being cleaned. The specific operation is as follows: Open the overflow discharge valve, and inject water or cleaning liquid into the cleaning pool until the cleaning liquid starts to overflow (it is recommended to use a scraper or similar tool to cut and apply floating oil towards the overflow port to promote its rapid flow). Keep the overflow discharge valve closed all the time to prevent accidental overflow from causing ground pollution. 9. Post-treatment of ultrasonic cleaning machine
Remove the cleaned parts, use compressed air to thoroughly blow off the residual cleaning liquid in each hole of the parts, and dry the surface (it is recommended to use a dust gun in conjunction with an air compressor). If conditions permit, it is best to install a water pool near the cleaning machine. So as to rinse the removed components. 10. When the cleaning machine has washed too many parts, the content of oil sludge in the cleaning agent will be quite high, coupled with the emulsifying effect of ultrasonic waves. The cleaning agent will weaken its cavitation ability due to excessive dirt and stickiness, and should not be used any longer. It is recommended that users configure a water storage bucket to be used in conjunction with the cleaning machine to settle overly dirty cleaning agents for recycling, thereby reducing costs. 11. The auxiliary effect of ultrasonic cleaning machine immersion
Many components, such as cylinder heads, pistons, connecting rods, turbochargers, intake and exhaust manifons, etc., carry carbon deposits on these components. Some of them are relatively light and can be easily cleaned, but some are very heavy. In such cases, the necessary immersion and softening process of the workpiece will achieve a better cleaning effect. The ultrasonic cleaning machine adopts the principle of ultrasonic cleaning and can achieve a thorough cleaning effect on objects. It is particularly ideal for cleaning deep holes, blind holes, and concave-convex grooves, without affecting the material or precision of any objects. At the same time, it can be used for extraction, degassing, mixing, cell disruption and nano-decomposition in biochemical, physical, chemical, medical, scientific research and experiments in colleges and universities. Making appropriate adjustments based on different situations is in line with the principle of saving and being effective. Especially techniques such as adding an appropriate amount of clean water or cleaning agent to the cleaning pool and reusing them can save and reuse items, reducing your costs while achieving the same effect. < / p > < p > the article from < a href = "http://www.kejeme.com" > < strong > ultrasonic cleaning machine < / strong > < / a > manufacturer, jie au release: http://www.kejeme.com/news/xyxw/1272.html